Back To Menu
Learning how to install a motherboard is your first stop in learning how to install computer components. The motherboard is attached one way or another to every device in your computer.
You will notice that the motherboard comes pre-configured with numerous slots where you can plug devices in.
Additionally, there are connectors and jumpers that you will need to set to make it work properly.
How to Install a Motherboard
- Be sure to have your documentation handy at all times. For the purposes of this tutorial we will be working with the standard ATX motherboard common to most mid-tower computers.
- Open the Case and Remove Motherboard Tray. The first step will be to open the case. The method for doing this will vary depending upon the case you have. For mid-towers, you will most likely have to remove a side panel that sits above where the motherboard will be.
- Unscrew the two screws holding this panel onto your computer and slide it out. Set the screws in a safe place. If you have an older style case you may have to remove all of the screws from the back of the chassis, and slide that out.
- If your case has a motherboard tray you will need to remove that as well. Some cases have removable motherboard trays meant to help you better install motherboard units correctly. These trays are quite useful and can make installing your motherboard much easier. If your case has such a tray, be sure to remove it as well.
- Replace the ATX Connector Plate and Align Motherboard with Case. If you check all the parts that came bundled with your motherboard, you will notice that it came with its own face plate. This might seem unusual, as your computer case will have an ATX face plate already installed. The problem here has to do with potential incompatibility. your ATX face place may have connectors arranged in a different pattern than the one that came with your case. Therefore, it's best to use the custom face plate that came with your motherboard. To swap out the computer case face plate, press both corners until it pops out. Snap the new plate in place, aligning the keyboard and mouse connectors to the side of the case where your power supply is installed.
- Install Standoffs and Secure the Motherboard. The next step in knowing how to install a motherboard involves alignment. You want holes from the case to mah the holes from the motherboard--however there's more to it than that. First, locate the mounting holes in the case or tray that will mah up with those of the motherboard.
- Now that you've found the holes, it's time to install the standoffs. Standoffs are basically brass or plastic pegs that will support the motherboard as it installed. These pegs or spacers come in different varieties; some will be brass while others will be plastic. Check which ones you have. If the standoffs are of the brass variety, you may need a hex tool of some sort in order to properly install them. Install the standoffs into the holes that you identified earlier.
- With the standoffs securely installed, it's time to secure the motherboard. Align the motherboard over your case or tray so that you can see the standoffs clearly through their mahing holes on the motherboard. Then begin from the center of the motherboard to screw the motherboard to your tray or case.
- After you complete that, continue clockwise, affixing the screws into the mounting holes in all of the corners of the board. As you can see, knowing how to properly install motherboard units to your PC involves more than just a few turns of the screws!
- Installing Critical Wires and Connectors. The next step in knowing how to install computer components like your motherboard is to install critical wires and connects. Just because your motherboard is physically installed doesn't mean it can communicate with the rest of your system.
- You'll have to connect some important wires and cables to complete the process. The first wires are the ones that hang loose from your case, like hard drive, power, reset and speaker leads. Consult your documentation to know how to plug these wires into their appropriate slots in the case.
- The next cable is the one that feeds juice to your motherboard, the 20 pin ATX power lead from your power supply. Plug that in the appropriate slot in the motherboard. Some newer computers like the Pentium 4 may also include an additional 4 pin 12v connector from the power supply, which you must plug into the motherboard as well. Check that all of the critical wires are secured. If you used a removable tray you can reinsert that into the case at this time.
- To install a motherboard it's important that you follow the steps in order.
- Also, consult your documentation first before you begin the process. It will let you know if there are any jumpers that you need to set before attempting your install. These settings may vary depending on the type of motherboard that you purchased.
- In most cases, with a new motherboard, you will need a new case and power supply as well
- It is usually a good idea to install your processor, heatsink/fan, and the RAM before installing the motherboard in the case.
- This will void and nullify any and all warranties on your pc.
- Make sure you ground yourself before doing anything on the pc.(If you are not sure what this is, don't even attempt to do anything with the pc.
from wikiHow - The How to Manual That You Can Edit
Article provided by wikiHow, a collaborative writing project to build the world's largest, highest quality how-to manual. Please find author credits at the original wikiHow article on How to Install a Motherboard.All content on wikiHow can be shared under a .